山西省网站建设,专门做二维码的网站,禁用 wordpress 自带 jquery,国家重大建设项目网站地址模型 默认最简单的编织复材#xff0c;编辑材料属性时发现基体属性设置正常#xff0c;各向同性材料#xff0c;但是纱线的材料属性却没有弹性性能的设置。 导出inp文件后#xff0c;导入ABAQUS中其实可以看到有两种材料#xff0c;纱线也是有属性的。 ABAQUS中修改属性的…模型 默认最简单的编织复材编辑材料属性时发现基体属性设置正常各向同性材料但是纱线的材料属性却没有弹性性能的设置。 导出inp文件后导入ABAQUS中其实可以看到有两种材料纱线也是有属性的。 ABAQUS中修改属性的话一来手动比较慢二来每次都要改所以考虑导出inp后直接先修改inp的材料属性试试 inp文件(ABAQUS计算后)
参考链接 *后面跟关键字视作某模块开始或结束 **后面跟注释 之后方便起见省略注释部分并进行简单整理
*Heading
*Preprint, echoNO, modelNO, historyNO, contactNO**
** PARTS
**
*Part, namePART-1*Node1, -1., -1., -0.01200000012, -0.899999976, -1., -0.0120000001...\*\*省略n多行大概是节点位置35307, 0., 0., 0.*Element, typeC3D8R1, 2, 43, 42, 1, 1683, 1724, 1723, 16822, 3, 44, 43, 2, 1684, 1725, 1724, 1683...\*\*省略n多行大概是单元的节点编号32000, 33579, 33620, 33619, 33578, 35260, 35301, 35300, 35259*Elset, elsetMATRIX1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16...\*\*省略n多行大概是单元编号31985, 31986, 31987, 31988, 31989, 31990, 31991, 31992, 31993, 31994, 31995, 31996, 31997, 31998, 31999, 32000
*Elset, elsetYARN01849, 1850, 1851, 1852, 1889, 1890, 1891, 1892, 1928, 1929, 1930, 1931, 1932, 1933, 1968, 1969...\*\*省略n多行大概是单元编号29270, 29271, 29272, 29273, 29309, 29310, 29311, 29312, 29349, 29350, 29351, 29352
*Elset, elsetYARN1...\*\*省略n多行大概是单元编号
*Elset, elsetYARN2...\*\*省略n多行大概是单元编号
*Elset, elsetYARN3...\*\*省略n多行大概是单元编号
*Elset, elset_PickedSet7, internal...\*\*省略n多行大概是单元编号** Section: Section-1-MATRIX
*Solid Section, elsetMATRIX, materialMAT0
1.,
*Orientation, nameOri-PART-1_TEXGENORIENTATIONVECTORS, systemRECTANGULAR
PART-1_TEXGENORIENTATIONVECTORS
1, 0.
** Section: Section-2-YARN0
*Solid Section, elsetYARN0, orientationOri-PART-1_TEXGENORIENTATIONVECTORS, materialMAT1
1.,
** Section: Section-5-YARN3
*Solid Section, elsetYARN3, orientationOri-PART-1_TEXGENORIENTATIONVECTORS, materialMAT1
1.,
** Section: Section-3-YARN1
*Solid Section, elsetYARN1, orientationOri-PART-1_TEXGENORIENTATIONVECTORS, materialMAT1
1.,
** Section: Section-4-YARN2
*Solid Section, elsetYARN2, orientationOri-PART-1_TEXGENORIENTATIONVECTORS, materialMAT1
1.,
*Distribution, namePART-1_TEXGENORIENTATIONVECTORS, locationELEMENT, TablePART-1_TEXGENORIENTATIONVECTORS_Table
, 1., 0., 0., 0., 1., 0.
1, 1., 0., 0., 0., 1., 0.
2, 1., 0., 0., 0., 1., 0.
...\*\*省略n多行
32000, 1., 0., 0., 0., 1., 0.
*End Part**
** ASSEMBLY
**
*Assembly, nameAssembly
*Instance, namePART-1-1, partPART-1
*End Instance
*Node1, 6.19999981, 1., 0.120000005
*Node2, 5.4000001, 1., 0.120000005
*Node3, 4.5999999, 1., 0.120000005
*Node4, 3.79999995, 1., 0.120000005
*Node5, 1., 1., 0.304800004
*Node6, 1., 3.79999995, 0.120000005
*Elset, elsetALLELEMENTS, instancePART-1-1, generate1, 32000, 1
*Nset, nsetALLNODES, instancePART-1-1, generate1, 35301, 1
*Nset, nsetCONSTRAINTSDRIVER0, instancePART-1-135302,
*Nset, nsetCONSTRAINTSDRIVER1, instancePART-1-135303,
*Nset, nsetCONSTRAINTSDRIVER2, instancePART-1-135304,
*Nset, nsetCONSTRAINTSDRIVER3, instancePART-1-135305,
*Nset, nsetCONSTRAINTSDRIVER4, instancePART-1-135306,
*Nset, nsetCONSTRAINTSDRIVER5, instancePART-1-135307,
*Nset, nsetEDGE1, instancePART-1-1, generate1682, 31940, 1681
*Nset, nsetEDGE2, instancePART-1-1, generate1722, 31980, 1681
*Nset, nsetEDGE3, instancePART-1-1, generate3362, 33620, 1681
*Nset, nsetEDGE4, instancePART-1-1, generate3322, 33580, 1681
*Nset, nsetEDGE5, instancePART-1-1, generate42, 1600, 41
*Nset, nsetEDGE6, instancePART-1-1, generate82, 1640, 41
*Nset, nsetEDGE7, instancePART-1-1, generate33702, 35260, 41
*Nset, nsetEDGE8, instancePART-1-1, generate33662, 35220, 41
*Nset, nsetEDGE9, instancePART-1-1, generate2, 40, 1
*Nset, nsetEDGE10, instancePART-1-1, generate1642, 1680, 1
*Nset, nsetEDGE11, instancePART-1-1, generate35262, 35300, 1
*Nset, nsetEDGE12, instancePART-1-1, generate33622, 33660, 1
*Nset, nsetFACEA, instancePART-1-11763, 1804, 1845, 1886, 1927, 1968, 2009, 2050, 2091, 2132, 2173, 2214, 2255, 2296, 2337, 23782419, 2460, 2501, 2542, 2583, 2624, 2665, 2706, 2747, 2788, 2829, 2870, 2911, 2952, 2993, 3034...\*\*省略n多行33415, 33456, 33497, 33538, 33579
*Nset, nsetFACEB, instancePART-1-1...\*\*省略n多行
*Nset, nsetFACEC, instancePART-1-1...\*\*省略n多行
*Nset, nsetFACED, instancePART-1-1...\*\*省略n多行
*Nset, nsetFACEE, instancePART-1-1...\*\*省略n多行
*Nset, nsetFACEF, instancePART-1-1...\*\*省略n多行*Nset, nsetMASTERNODE1, instancePART-1-11,
*Nset, nsetMASTERNODE2, instancePART-1-141,
*Nset, nsetMASTERNODE3, instancePART-1-11681,
*Nset, nsetMASTERNODE4, instancePART-1-11641,
*Nset, nsetMASTERNODE5, instancePART-1-133621,
*Nset, nsetMASTERNODE6, instancePART-1-133661,
*Nset, nsetMASTERNODE7, instancePART-1-135301,
*Nset, nsetMASTERNODE8, instancePART-1-135261,
*Nset, nsetRP16,
*Nset, nsetRP25,
*Nset, nsetRP34,
*Nset, nsetRP43,
*Nset, nsetRP52,
*Nset, nsetRP61,
*Nset, nsetbackbc, instancePART-1-1, generate1, 35261, 41
*Nset, nsetbackbc1, instancePART-1-11,
*Nset, nsetbackbc42, instancePART-1-142,
*Nset, nsetbackbc83, instancePART-1-183,
*Nset, nsetbackbc124, instancePART-1-1124,
...\*\*省略n多行
*Nset, nsettopbc35300, instancePART-1-135300,
*Nset, nsettopbc35301, instancePART-1-135301,
*Nset, nsettops, instancePART-1-13323, 3324, 3325, 3326, 3327, 3328, 3329, 3330, 3331, 3332, 3333, 3334, 3335, 3336, 3337, 33383339, 3340, 3341, 3342, 3343, 3344, 3345, 3346, 3347, 3348, 3349, 3350, 3351, 3352, 3353, 3354...\*\*省略n多行
*Nset, nsettops3323, instancePART-1-13323,
*Nset, nsettops3324, instancePART-1-13324,
...\*\*省略n多行** Constraint: E-1-bbedge-fbedge1682
*Equation
3
bbedge1682, 1, 1.
fbedge1722, 1, -1.
RP4, 1, 1.
** Constraint: E-1-bbedge-fbedge3363
*Equation
3
bbedge3363, 1, 1.
fbedge3403, 1, -1.
RP4, 1, 1.
...\*\*省略n多行*End Assembly**
** MATERIALS可以看到这边更改材料属性
**
*Material, nameMAT0
*Elastic3.5, 0.346
*Expansion6.5e-06,
*Material, nameMAT1
*Elastic, typeENGINEERING CONSTANTS
141.14, 6.50, 6.50, 0.30, 0.30, 0.34, 4.85, 4.85
2.52,
*Expansion, typeORTHO-2e-07, 3e-06, 3e-06
*Distribution Table, namePART-1_TEXGENORIENTATIONVECTORS_Table
coord3d, coord3d**
** PREDEFINED FIELDS
**
** Name: Field-1 Type: Temperature
*Initial Conditions, typeTEMPERATURE
ALLNODES, 0.*Step, nameStep-1, nlgeomNO
*Static
1., 1., 1e-05, 1.**
** BOUNDARY CONDITIONS
**
** Name: E11-1 Type: 位移/转角
*Boundary
RP4, 1, 1, 0.8**
** OUTPUT REQUESTS
**
*Restart, write, frequency0**
** FIELD OUTPUT: F-Output-12
**
*Output, field, variablePRESELECT**
** HISTORY OUTPUT: H-Output-2
**
*Output, history
*Node Output, nsetc1
RT, **
** HISTORY OUTPUT: H-Output-1
**
*Output, history, variablePRESELECT
*End Step
